View Larger Image A successful pot—even one so simple as a chip and dip—is created by understanding its function and constantly evaluating how the pieces go together.

July 4, 2007

The Chip and Dip: Combining Snacking Form and Function

by Steve Davis-Rosenbaum | Read Comments (5)

After a long day in the studio, I often unwind and relax by watching a movie while snacking. Going to the kitchen, I collect the appropriate pots, bag of chips, dip and drinks. Carefully juggling all these items back to the couch, I sometimes spill dip and chips along the way. After cleaning the mess, I can finally relax.

Practical issues based around comfort, convenience and food are a rich source of inspiration. As a potter focusing on function and form, what could I create to ease the schlepping of my chips and dip? Successful pots are created by understanding the function and constantly evaluating how the pieces go together. The challenge here is not to just remake the chip and dip, but to use it as a jumping off point to inspire new forms and designs.

Designing a Chip and Dip
When deciding on size, envision the amount of chips and the quantity of dip required for the chips before you start making bowls. I usually make five sets bowls and straps then mix and match the parts till each becomes aesthetically pleasing. If needed, I go back to the wheel and remake bowls.

Throwing the Bowls
I throw all the pieces in the same sitting and create 4–5 sets at a time. Depending on the firmness of the clay and rate of drying, I plan my studio schedule to have a 3–5 day period to work on the multiple forms. I also throw multiple parts for each chip and dip, allowing myself to make critical aesthetic decisions during assembly. By working on several chip and dips at the same time, new ideas develop while I work on each pot. This design requires two bowls for the construction/assemblage, which should be proportional to each other and, when placed side by side or held on top of each other, give the sense of belonging together.

Allow the bowls to set up and reach the soft side of leather hard. Completely finish the large bowl by cleaning the rim and trimming the foot before adding any other parts. Cut and manipulate the small bowl to fit the shape of the strap later.

Making the Strap/Handle
Throw the strap as a donut, opening the clay all the way to the wheel head and pulling the walls of the clay to the edge of the bat. To finish the walls of the strap, taper the rim. Cut and let set up to the soft side of leather hard. Turn the donut upside down and trim the bottom of the strap then shape it to match the thrown end. Place the strap on a canvas and cut one end, then move each end to create a shape for the desired design. Remember, the top will hold the smaller pot and the shape needs to allow hands to enter and leave with chips. Let stand to set up more so it can stand on its own.

Assembly
Since there are multiple pieces to the Chip and Dip, timing and attention to the attachment areas is very important. Before the pot can be assembled, all the pieces need to be at the correct stage of leather hard. To control the drying time, the pot stays covered in plastic until the desired firmness is reached. Sometimes spraying pieces with water and covering to maintain correct firmness is necessary. To view larger pictures of the ones at right, showing you how to make a chip and dip, click here.

When the pieces are ready, mark the location of the handle on the large bowl, and score the rim. Shape the handle making sure the ends of the strap are wide enough to straddle the large bowl. When the handle can stand on its own, score and slip the ends and attach it to the large bowl. Using a soft sponge, chamois or fingers, stretch the strap (like pulling a handle) into shape to change the tension of the clay and prevent warping and twisting. Support the handle in the center with a prop made from leather hard clay. Place a piece of paper between the prop and the clay parts to ensure easy removal. With the prop still in place, hold the small bowl up to the handle, making sure the shape and proportion work well. Cut the bottom edge to match the curve of the top of the strap. I rework the tension, alignment and shape of the strap and check all previous attachments.

Timing Is Everything!
For multi-piece projects, all parts need to dry at the same rate. Depending on studio conditions, spraying the form with water throughout the process might be necessary. After adding each piece, wrap the piece in plastic to slow the drying. It might be necessary to wrap sections of the pot if one area starts to dry faster than another. It is best to work on the chip and dip over a few days, leaving time for areas to set up to support attachments and desired forms. 

Attaching the Small Dip Bowl to the Handle
Score and slip the edges of the bowl and handle before attaching the small bowl to the handle. Place a coil around the inner and outer seams to help secure the bowl. Be sure to work in the clay and blend it so the coils disappear. After the bowls set up to leather hard, add handles to top bowl and trim the rim of the large bowl. I find that this visually finishes the form creating one new form from many parts. Make sure the strap can support the top bowl and will not lean over. Check it often and adjust as it dries. Clean rims and attachments. Cover and let the piece dry slowly.

Finishing Touches
I go back to the attachment of the strap and add coils of clay to blend in the edges and round the rim, leaving no gaps or unfinished edges. I let the pot dry slowly to minimize warping and leaning.

About the Author
Steve Davis-Rosenbaum has been a potter since 1978 and operates SDR Pottery in Lexington, Kentucky. He works in earthenware and decorates in the majolica style. For questions or comments, contact Steve at darogallery@insightbb.com.